How to use Caulker patch without internal walls plaster them

I know it can be a headache for most people, but did you know that it is sometimes possible that the domestic "DIY" enthusiasts, as well as the builder to settle nasty nicks, scratches and cracks before painting the interior walls without being plastered all over the area again.

Available in many "DIY" store is a wonderful tool, which is called "Caulker."

What is a "Caulker"?

is essentially a flexible plastic-type blade, generally about 10 to 12 "in length and can be used for applying a filler the surface of a wall or ceiling, and also the elastic capability of being able to pen (Blend: Flatten) of . filling gently out onto the surface, making it ideal for spot on

a 'Caulker' is very similar to the "Texturing / Arte Xing legs' unless the business edge of the" Caulker & # 39; smooth and flat, not serrated, combs and the like, such as a "Texturing comb & # 39;. report

There are generally two types of plastic" Caulker. & # 39; One is an all-in-one plastic version, while the thicker grip molded onto the thinner flexible working lives. The rest consists of a wooden handle, and a separate, flexible and thinner plastic working edge is inserted into the wooden handle.

next to the & # 39; Caulker "successfully apply the label and prepare the new plaster wall / table decorating before the ceiling is an invaluable tool for yourself and use it if you do not own" DIY "

1: you will be able to scoop up joint filler bucket using scraper and then strip material from the center of the "Caulker" blade

2. Start to offer employees a filler "Caulker" the surface of the wall, resting on the flat directly, and the entire surface with a 45% angle

3: and if we continue to slip in the 'Caulker' to the wall, lay the material slowly close the 45% angle so that at the end of the stroke of the handle edge closer to the wall, which is the minor scratches and surface variations as you go.

This method is "on" should be a continuous uninterrupted.

4 : Once it's done, take your scraper and scrape off the filler own "Caulker"

5: and begin to use the pure "Caulker" feather the edges of the filler onto and over a good area of ​​the surface .

As with most things, first tried, it all takes a lot of practice.

production of the vital key. Please watch out for the rest of the article, which covers all kinds of different surfaces and how to prepare them, before the great or decorating.

There is a wide selection of fillings available in the market that can be used in our "Seal Technique" and has experimented with most of them.

I find that the best results are achieved when mixed with 40-50% run / end "type of gypsum plaster pink" white powdered filler-type inner surface clean with cold water.

This ultimately creates a very fine mixture which is ideal for the job.

Once you have created the filler, the consistency should be thick enough, you can not run or drip when the scraper scoop some up. And do not be so thick that you can not even spread out onto the surface.

Also make sure that all of these mixed clumps.

Again, it is essential to use clean water and clean all equipment. The reason is that once you have laid the surface of the filler, if there is a bit of mud mixture as you are smoothing the surface of the filler, it is noticed that a few minor scratches in your work.

There are many substances that are mixed with water tends to shy away once dried.

Thus, the second layer may be feasible area when dry. To do this, you need to define more mixed material over a wider first attempt and beyond the first layer completely covers.

But before we go on this second layer, read in connection with the preparation of the preliminary decorative interior surfaces, because we have just created a highly porous surface and the band's new material does not stick to just pass the dried stuff.

This is the mix of fillers that have created absolutely wonderful for grinding down; This may be required in that they further mix the filler in the wall.

Use fine sandpaper, and please take care when using sharp tools in use, always read the instructions on the packaging and building materials, use a dust mask and take care of the lungs.

For more on how to use the "Caulker" taping new plaster wall / ceiling boards were for "Texture awakening."

I hope this article regarding a 'Caulker' to sort out the internal surfaces help to "DIY" mission.

Go Create a Craze.

Dale Ovenstone. 2008

Source by Dale Ovenstone

Leave a Reply

Your email address will not be published. Required fields are marked *